|
I made a collet organiser for mill drawer. The size of the holes was very sensitive. I made holes slightly larger, say 1mm, then collets dropped through the holes.
引出しの中に入れるコレットスタンドを作りました。穴径がかなり微妙です。奥のやつは失敗作。穴がほんの1mmほど大きすぎコレットが下に抜けてしまった。
|
|
I made a end mill stand from an off cut of 2X4. Round nose end mills are seen here, but I have no intension to use them at the moment. A Chinese supplier made a mistake and sent me these instead of normal end mills. The sending back cost was about the same as these mills. So I decided to buy them. The supplier sent me correct mills with some extras later.
2X4の切れ端でエンドミルスタンドを作りました。先丸のエンドミルが見えますが、中国の通販屋が間違えて送ってきてしまったものでとりあえず使う予定はありません。送り返す送料がこの6本のエンドミルと同じくらいだったので、送り返すのもばかばかしいので、引き取ることにしました。その後、正しいエンドミルを送ってきたのですが数本おまけが入ってました。
|
|
Organised mill drawer. I made separators with 12mm MDF.
フライス盤の引出しの中。12mmのMDFで仕切りを作りました。
|
|
The change gears were supplied in a plastic bag and looking for correct gear in a bag was quite messy. So I decided to make a gear organiser. At first cut grooves on 6mm MDF with a router.
旋盤用の歯車がいっぱいビニール袋の中でごろごろしています。一部の歯車の歯数の刻印も読みにくいし、整理箱を作ることにしました。6mmのMDFにラウターで溝を彫り。
|
|
3mm MDF separators added.
3mmMDFの仕切りをつけて完成。
|
|
Now gears are very well organised.
歯車を探すのも簡単です。
|
|
Now I have many dies. They also need an organiser.
ダイスも結構増えてしまったので、これも整理箱を作ることにしました。
|
|
I made an organiser from 1.5mm styrene sheets. At first made a ladder like structure. This part would hold 20mm dies.
ダイスは小さいし、結構数があるので、スチロール板で作ることにしました。1.5mmの板でこんなはしごみたいなものを作ります。それは20mmのダイスが入る部分。
|
|
Other ladder added for 25mm dies.
さらに25mm用のはしごを追加し。
|
|
Bottom was added and 5mm triangle styrene added to both sides.
底を付けて、両側にダイスのサイズを記入するための、5mm三角棒を接着。
|
|
Organised dies.
ダイスを入れるとこんな感じです。
|
|
However I found it bit hard to pick up 20mm dies from this organiser and added 3mm square styrene rods to 20mm compartments to push dies up.
ところが、25mmはともかく、20mmは深く沈みこみ過ぎて取り出しにくい。3mm角のスチロール棒を接着して、かさ上げしました。
|
|
I made tap and reamer stand from two sheets of 16mm MDF glued together.
ついでに16mmのMDFを二枚張り合わせたものでタップとリーマーのスタンドを作りました。
|
|
Inside of the lathe drawer.
旋盤の引き出しの中身です。
|