I was not happy with some parts of my triangle bridge. So I modified it.

三角橋なんであるが、どうしても気にくわないところがあり改修することにしました。

I used brass nails as bolts. They did not look impressive at all. Also the gussets seemed bit too thin.

本来ボルトであるところを真鍮釘で代用してしまったところと、ガセットが薄すぎるところです。これらを作りなおすことにします。

I made a master of the bolts from styrene. I intended to make them from white metal instead of resin. So the parting line of the mould should be as shown by yellow line.

スチロール材でボルトの原型を作ります。レジンではなくホワイトメタルで鋳造する予定なので本来型の分割線は黄色の線のようにするべきですが、

However with above parting line burs were expected on the surface of the products. So I decided to make the parting line as show here.

バリ取りが面倒そうなのでこの部分で分割すると言う乱暴な方法に出ました。


The inside of the silicon moulds were as this.

シリコン型の内側はこのようになってます。真ん中に入ってるのはマスター。

 


I cut the pouring port as this. Obviously in this arrangement you might think the product would not come out. However I could manage to release the product easily from the moulds.

外側には湯口をほりました。普通に考えればこの湯口から湯を流し込んだら抜けなくなるはずですが、大丈夫、抜けます。

After pouring molten white metal, I waited to let it cooled down enough. I levered the arrowed part with a screw driver to break the product in two parts. It worked well.

湯を流しこんで、十分固まったところで矢印の部分をドライバーでこじれば押湯部分だけが左の用にちぎれて出てきます。このとき半端に固まった状態でこじると押湯の真中付近でちぎれてしまうので面倒なことになります。

Mass-produced bolt heads. Pointed end of products was produced by my forced levering. White metal sets much quicker than resin and suitable for mass-production.

量産したダミーボルト。無理やりちぎったので先端が伸びているのがわかります。ホワイトメタルはすぐ固まるので量産にはレジンより向いています。

I remade the gussets from 1mm styrene sheet.

ガセットは1mmのスチロール板で作り直し。

All parts were painted with rust coloured primer.

錆色のプライマーで塗装。

It seemed much better than before. I applied the paint directly to the cast metal surface. It was a failure. The paint easily peeled off. The surface should be roughed by wire brush or something.

ご覧のように非常に良くなりました。ただし、ホワイトメタルにそのまま塗装したのは失敗で、鋳造の表面はとても滑らかなので塗料が良く乗りません。ワイヤーブラシで表面を荒らすとかしたほうがいいようです。

The upper and lower structures were permanently fixed before. However it was incontinent. So I made the upper structure removable by pins.

以前は橋の下部構造と上部構造が一体だったんですが、上部だけしまえるように分割式とすることにしました。簡単なピン結合とします。

Making holes for pins.

ピン用の穴をあけます。

Modified triangle bridge.

改修の完了した三角橋です。


 

 
inserted by FC2 system